1. For the newly installed furnace body, before commissioning, carefully check whether the gas meets the requirements of the burner; check whether the detection instruments on the gas supply pipeline are normal and whether the opening and closing of the pipeline valves are normal, and whether it is convenient for future use and maintenance.

2．對新安裝的管道，應認真檢查所有管路的安裝可靠性和管路的密封性。

2. For newly installed pipelines, the installation reliability and sealing of all pipelines shall be carefully checked.

3．使用單獨氣化站的用戶，要保證供氣量、供氣參數符合燃燒要求。

3. Users who use separate gasification station should ensure that the gas supply quantity and gas supply parameters meet the requirements of safe combustion.

4．操作人員認真閱讀設備使用說明書，熟練掌握操作知識及方法。

4. Operators carefully read the equipment operation manual and master the knowledge and methods of safe operation.

5．天然氣鍋爐燃燒器每次開機前要檢查燃氣閥門是否打開，否則燃燒器不工作。

5. Check whether the gas valve is open before starting the burner of natural gas boiler, otherwise the burner will not work.

6．啟動控製櫃上的電源控製按扭，此時數顯表就顯示當前爐內溫度，新安的裝爐體此溫度為環境溫度。

6. Start the power control button on the control cabinet. At this time, the digital display will display the current temperature in the furnace. This temperature of Xinan furnace charging body is the ambient temperature.

7．啟動風機控製按扭，安裝在爐體上的風機就工作，此時若風機損壞控製櫃就自動保護不進入下一步操作。

7. Start the fan control button, and the fan installed on the furnace body will work. At this time, if the fan is damaged, the control cabinet will be automatically protected from further operation.

8．助燃風機工作無異常現象時，再啟動燃燒控製按扭，此時燃燒程序控製器就開始工作，它通過一定的程序進行點火、送氣、檢測火焰、等程序更終實現燃燒。

8. When there is no abnormal phenomenon in the combustion fan, the combustion control button will be started again. At this time, the combustion program controller will start to work. It will carry out ignition, air supply, flame detection and other procedures through certain procedures, and finally realize safe combustion.

9．天然氣鍋爐燃燒器當燃燒控製器收到不利於燃燒的信號（例：點火失敗、氣壓不穩定、電路有問題）等問題時，燃燒控製器就立刻關閉燃氣並發出報警信號。

9. When the combustion controller receives the signal that is not conducive to combustion (e.g. ignition failure, air pressure instability, circuit problems) and other problems, the combustion controller will immediately shut down the gas and send out an alarm signal.

10.燃燒控製器若報警，必須是故障後由操作人員對其手動複位才可以繼續工作。

10. If the combustion controller gives an alarm, it must be reset manually by the operator after the fault is solved.

11.整個設備的操作，操作人員應參考爐體操作規程及k8凯发官网入口工藝要求進行操作。

11. For the operation of the whole equipment, the operators should refer to the furnace safety operation regulations and production process requirements.

12.按k8凯发官网入口工藝要求需要調整控製溫度時，操作員應參考智能數控表說明書進行調節。

12. When the control temperature needs to be adjusted according to the production process requirements, the operator should refer to the manual of intelligent numerical control table for adjustment.

（二） 天然氣鍋爐燃燒器關機操作

（2） Shutdown operation of natural gas boiler burner

（1）關機有兩種情況：是：當爐內溫度到達所設定值自動關機，此時操作員不必任何操作，等到爐內溫度低於設定值時控製器會自動開機。

(1) There are two cases of shutdown: the first is: when the furnace temperature reaches the set value, the operator does not need any operation, and the controller will automatically start up when the furnace temperature is lower than the set value.

（2）第二是：人為停機和交接班停機時，此時操作員應按開機時的相反順序（a.先關閉燃燒控製按扭、b.再關閉風機按扭、c.關閉電源按扭）操作關機。

(2) The second is: in case of man-made shutdown and shift change shutdown, the operator should operate and shut down in the reverse order (A. first turn off the combustion control button, B. then turn off the fan button, C. finally turn off the power button).

（3）天然氣鍋爐燃燒器關機時間較長情況下操作員應關閉燃氣管路閥門，以免燃氣泄漏現象發生。括和常識考查。內容概括摘原文，常識考查適當須積累文學、文化常識。

(3) When the burner of natural gas boiler is shut down for a long time, the operator should close the gas pipeline valve to avoid gas leakage. General knowledge examination. It is necessary to accumulate common knowledge of literature and culture.