要看普瑞泰鉛防護門的製作工藝
First of all, we need to see the production process of pretai lead protective door
1：測量門洞口
1: Survey door opening
2：根據門洞口計算出門的規格尺寸
2: Calculate the size of the door according to the door opening
3：焊鋼架（門體的骨架，材料：30mm*30mm的矩形鋼管）
3: Welded steel frame (frame of door body, material: 30mm * 30MM rectangular steel pipe)
4：用機器熱壓鉛合成板
4: Hot pressing lead composite board with machine
5：製作門體（一麵鉛合成板，一麵密度板材）
5: Making door body (one side of lead composite board, one side of density board)
6：門框料製作（裏麵做好鉛板防護，要求，和扇搭接）
6: Production of door frame material (internal lead plate protection, requirements, overlap with leaf)
7：門扇上麵板（1mm冷板靜電烤漆麵板）
7: Upper panel of door leaf (1mm cold plate electrostatic paint baking panel)
8：組裝門扇和門框（合頁為加重不鏽鋼合頁）
8: Assemble door leaf and frame (hinge is weighted stainless steel hinge)
9：安裝，要求門框和牆部的防護搭接處理，達到開啟方便，不露線）
9: For installation, it is required that the door frame and the wall should be protected and lapped to make it easy to open without exposing the line.)
10：門扇下部距離地麵間隙不超過5-8mm（處理好下部防護）
10: The gap between the lower part of the door leaf and the ground shall not exceed 5-8mm (handle the lower part protection)
11：鎖部位專用防護用鎖，內部做好鉛防護處理，達到門鎖部分不露線
11: The lock part is specially used for protection, and the lead protection treatment shall be done inside to ensure that the part of the lock is not exposed
在看看牆麵的鉛防護施工：
Take a look at the lead protection construction of the wall:
1、牆麵的射線防護施工分鉛板，鉛合成板施工兩種
1. The radiation protection construction of the wall is divided into lead plate and lead composite plate
2、鉛板鉛合成板施工就是把鉛板用熱壓機把鉛板和密度板合成在一起
2. The construction of lead composite board is to combine lead board and density board with hot press
3、把鉛合成板固定到牆麵上一般采用：搭接防護施工方法
3. The lead composite board fixed to the wall is generally used: lap protection construction method
4、過孔定子開關盒，網線等孔洞做鉛板防護處理
4. Through hole stator switch box, network cable and other holes do lead plate protection treatment
5、鉛板的外表層一般是石膏板，塗料處理方法和鋁塑板飾麵方法
5. The outer surface of lead board is generally gypsum board, coating treatment method and aluminum-plastic board finishing method
6、保證了整個房間的防護施工達到搭接節點，保證不會產生露線。
6. The protection construction of the whole room is ensured to reach the lap joint, and no exposed line is guaranteed.
在鉛門的施工中一定要注意鉛門的框體和門洞牆壁之間的縫隙，會產生露線，和門鎖，門扇下部離地高等原因照成的露線
In the construction of the lead door, we must pay attention to the gap between the frame of the lead door and the wall of the door opening, which will produce the exposed line, and the exposed line caused by the door lock, the lower part of the door leaf from the ground
在鉛門的施工中一定要注意鉛門的框體和門洞牆壁之間的縫隙，會產生露線，和門鎖，門扇下部離地高等原因照成的露線
In the construction of the lead door, we must pay attention to the gap between the frame of the lead door and the wall of the door opening, which will produce the exposed line, and the exposed line caused by the door lock, the lower part of the door leaf from the ground
The highlights of this article are shared by the highlights provided by radiation protection equipment. For more highlights, please click our website: //www.ysyfd.com , we will have more wonderful content waiting for you to check, welcome to inquire
18678809986
